The OTC 25 ton shop press is a tough and economical press that is ideal for pressing rear axle bearings, piston pins, and much more. With its large 30 inch x 46 inch work area under ram makes positioning of even bulky work easy. The press bed is easily raised and lowered by a dependable lifting mechanism. Press comes complete with No. 4002 hydraulic hand pump, No. 9652 gauge, No. 24815 tee, No. 9767 hose (1/4 inch ID x 6 feet), hydraulic ram No. 51426 with 6-1/4 inch stroke, and 42733-WH2 pump mounting bracket.
Amtrol RP-15HP Pressuriser 15 GPM (2201-39)The AMTROL High Performance Pressuriser (RP-HP Series) is a pre-packaged system perfect for single and multi-family dwellings and can truly increase the water pressure in your home. High water pressure has enormous benefits, not only regarding comfort and convenience, but also in improving how appliances operate. The AMTROL High Performance Pressuriser; is designed for cold drinking water applications where the supply of city water pressure is at or above a flow pressure minimum of 10 psig where the pressure is considered too low to meet household standards. Make living with inadequate water pressure a distant memory.Amtrol RP-15HP Pressuriser Benefits:; Dishwasher performs better; Dishes are cleaner; Turf/irrigation system provides better coverage; Eliminates brown spots on lawn; Faster water from fixtures; More power in your shower; Multiple fixtures; Higher delivery pressureAmtrol RP-15HP Pressuriser Features:Anybody can pump up pressure with standard off-the-shelf pump and tank components, however AMTROL does it right. The AMTROL High Performance Pressuriser has been designed from the ground up specifically for pressure boosting applications. The High Performance Pressuriser incorporates special safety features designed to protect your product, prevent pump burn-out and optimize performance. The AMTROL High Performance Pressuriser; is only one of a full line of quality AMTROL products designed, engineered and built by professionals for professionals.Amtrol RP-15HP Pressuriser Specifications:; The pump motor is designed for use with single phase 60 Hz Ac.; All models are pre-wired for 115 Volt.; All pumps can be re-wired to be used with 230 Volt.; The power for your pump must be on a separate circuit. Use a 20 amp. circuit with 115 volt and use a 15 amp. circuit with 230 Volt.; Maximum Temperature Rating = 110;FSee images for unit specific specifications.* Additional charge for residential delivery.
Amtrol-Well-X-Trol 44 Gallon Water System Pressure Tank with Composite Base - WX-250D
The Well-X-Trol WX-250D pressure tank floor stand model is specifically designed for larger homes and institutions such as country clubs farms nursing homes etc. This handles the demands of larger systems in a minimum of space.Exclusive butyl diaphragm along with the 100% corrosion resistant virgin polypropylene liner are secured by a positive hoop ring seal for added strength and reliability. This totally integrated system outperforms other types of water chamber designs.The stainless steel air valve is welded rather than threaded to prevent loss of air pressure.The finest quality custom mill steel is used in the deep drawn dome for extra strength while keeping tank weight to a minimum.Note:Â All tanks are pre-pressurized at 38 PSI and should always be set 2 PSIÂ below the cut in of your pressure switch. It is recommended to check tank pressure before installation. Pressure switch settings should not exceed a 20 PSI differential between cut in and cut out.Installation Operation and Maintenance for Well-X-Trol tanksÂ PDF 1MB
Built into every fuel transfer pump, chemical transfer pump and meter is over 50 years of experienceâ€”and the pride and workmanship associated with the moniker Made in USA. We use only the most durable materials to insure long life and dependability. Fill-Rite and Sotera branded products deliver superior performance time and time again, regardless of the application or installation. The FR3200 Series offers two options: the FR3204 (pump only) and the FR3210B, which includes a 1-inch ultra-high-flow automatic nozzle and an 18-foot, 1-inch hose with a static wire. Fill-Rite also offers a wide range of accessories that can make your job even easier. The FR3200 is compatible with their 900D and 901 Series Meters. Speed, mobility, flexibility, reliability-the FR3200 brings it all to the job. And best of all, it's a Fill-Rite, the best value in the pump industry, made right here in the USA.
This Enerpac RC-256 single-acting alloy steel hydraulic cylinder with 25-ton capacity has a round body with one port and spring-return of the single piston rod with 6.25" stroke for use in general-purpose applications in any position. The single-acting hydraulic cylinder uses liquid pumped through its single port for rod extension and a pretensioned internal spring for expedited rod retraction to produce continued movement. A built-in stop ring prevents the plunger from extending beyond the stroke length, assists in absorbing side loads, and can endure the full capacity of the cylinder. The plunger wiper helps inhibit contamination in the cylinder, and the removable grooved plunger saddle covers the plunger mounting threads and protects the plunger during lifting operations. The GR2 bearings reduce wear and help prevent jamming and rod over-extension by absorbing eccentric load stresses. The port is a quick-connect CR-400 female coupler for use with a CH-604 male coupler (sold separately), and the included dust cap covers the port when not in use. The high-strength alloy steel body has a baked enamel finish for corrosion resistance in harsh environments.SpecificationsCylinder capacity25 tons (25.8 maximum)Stroke length6.25 inchesEffective area5.16 square inchesOil capacity32.23 cubic inchesCylinder bore diameter2.56 inchesCollapsed height10.75 inchesExtended height17.00 inchesOutside diameter3.38 inchesWeight22 lb.Enerpac manufactures high-pressure tools and equipment for industrial applications. The company, founded in 1910, is headquartered in Menomonee Falls, WI.
The Enerpac PA-133 single-speed hydraulic air pump is for lifting, bolting, or applying pressure with a hydraulic cylinder (sold separately) in plant maintenance, fabrication, production, bolting, vehicle repair, and other applications where compressed air is the preferred power source. It has a three-way control valve for advancing, releasing, or holding a single-acting cylinder. This single-speed pump is for applications with a constantly applied load. The pump is controlled by a treadle that can be operated by hand or by foot. The pump can be operated in either a horizontal or vertical orientation. A swivel coupling provides access to hydraulic connection and pump operation. An internal pressure relief valve helps protect the pump from overload. The pump has base mounting slots. The pump has 3/8" and 1/4" National Pipe Taper (NPT) threads ports for connecting to an air supply or attaching a hose or gauge (sold separately).SpecificationsMaximum operating pressure10,000 pounds per square inch (psi)Maximum output flow rate, per minute, at 0 psi (100 psi inlet pressure)40 cubic inchesMaximum output flow rate, per minute, at 10,000 psi (100 psi inlet pressure)8 cubic inchesUsable oil capacity36 cubic inchesInlet air-pressure range60 to 120 psiAir consumption, at 100 psi9 standard cubic feet per minute (scfm)Maximum operating noise level85 decibels (A)Valve type3-wayWeight12 lb.Dimensions5.71 x 5.62 x 14.69 inches (H x W x D)H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from back to front.Hydraulic pumps lift, bolt, or apply pressure to objects by pressurizing and moving hydraulic fluid. A hydraulic pump consists of a base, a reservoir that holds hydraulic fluid, and an operating mechanism, such as a handle or foot pedal, an electric motor, compressed air, or a gasoline engine. When the operating mechanism is activated, pressurized hydraulic fluid from the reservoir is delivered through an attached hose to ...
OTC (4131) 10-Ton Spring-Return Hollow Center Hydraulic Ram
The OTC 4131 is ideal for push/pull applications found in off-highway construction mining and other industries where heavy equipment is maintained. Center hole permits extending screws cables etc. straight through the ram for versatility of application. Rams withstand full "dead-end" loads. Chrome-plated piston rods resist wear and superior packing's and seals provide high cycle life without leakage. Piston head inserts are interchangeable for versatility and tapped base mounting holes provide easy installation in fixed applications. 10-Ton capacity 2-1/2" stroke and a 49/64" center hole diameter. Retracted height is 5-5/16" and the extended height is 7-13/16".
The Enerpac P-80 high-pressure, two-speed hydraulic hand pump is for lifting, bolting, or applying pressure with a hydraulic cylinder (sold separately) in intermittent and non-repetitive construction, manufacturing, and maintenance and repair applications. It can advance and release a single-acting cylinder. This two-speed hand pump requires fewer handle strokes to move a load than a similarly rated single-speed pump, increasing productivity. An internal pressure relief valve helps protect the pump from overload. The vent-free reservoir helps prevent oil from spilling and is for use in non-vented applications. The pump can be operated in either the horizontal or vertical position. The steel body resists corrosion and wear, and the chrome-plated plunger and wiper system help extend the life of the pump. An ergonomically designed grip helps reduce operator hand fatigue, and the pump has a built-in carrying handle for transport. The pump has a 3/8" National Pipe Taper (NPT) threads port for connecting to a hose or gauge (sold separately).SpecificationsMaximum operating pressure, first stage500 pounds per square inch (psi)Maximum operating pressure, second stage10,000 psiMaximum oil displacement, per stroke, first stage1.00 cubic inchMaximum oil displacement, per stroke, second stage0.15 cubic inchUsable oil capacity134 cubic inchesPiston stroke1.0 inchMaximum handle effort77 lb.Weight23.6 lb.Dimensions7.65 x 20.12 x 5.91 inches (H x W x D)H is height, the vertical distance from lowest to highest point; W is width, the horizontal distance from left to right; D is depth, the horizontal distance from back to front.Hydraulic pumps lift, bolt, or apply pressure to objects by pressurizing and moving hydraulic fluid. A hydraulic pump consists of a base, a reservoir that holds hydraulic fluid, and an operating mechanism, such as a handle or foot pedal, an electric motor, compressed air, or a gasoline engine. When the operating mechanism is activated, pressurized hydraulic fluid from the reservoir is delivered through an att...
This high quality cooler is fitted with 120' of Stainless Steel coils. 100' of 3/8" OD and 20' of 1/4" OD coil makes it a perfectly balanced system for a smooth flow of beverage. Fitted with wall coupling ,shank and washer for leak proof setup. Includes chrome plated brass faucet and faucet knob. We construct our Jockey Boxes in high quality Coleman Coolers. Connections between Coupling and Coils are made with Beer Nut, Ferrule and special grommet.
OTC 3-Position/4-Way Manual Valve A 3-position/4-way lever operated detent positioned valve for use with double-acting rams. It has "advance" "neutral" and "return" positions. Cylinder ports are blocked in "neutral" and pump flow is directed back to the reservoir.